/*  EEPROM24LC256v1
 *  16/03/2022
 *  Checks 24LC256 external EEPROM is connected
 *  Reads and writes bytes to and from EEPROM
 */
//Wire library required as EEPROM run on I2C
#include "Wire.h"
#define disk1 0x50    //Default Address of 24LC256 eeprom chip in Board

//I2C scanner used on start up to mkake sure eeprom is alive and well
 void scani2c(){
  byte error, address;
    int nDevices = 0;

  Serial.println("Scanning...");

  for (byte address = 1; address < 127; ++address) {
    // The i2c_scanner uses the return value of
    // the Wire.endTransmission to see if
    // a device did acknowledge to the address.
    Wire.beginTransmission(address);
    byte error = Wire.endTransmission();

    if (error == 0) {
      Serial.print("I2C device found at address 0x");
      if (address < 16) {
        Serial.print("0");
      }
      Serial.print(address, HEX);
      Serial.println("  !");

      ++nDevices;
    } else if (error == 4) {
      Serial.print("Unknown error at address 0x");
      if (address < 16) {
        Serial.print("0");
      }
      Serial.println(address, HEX);
    }
  }
  if (nDevices == 0) {
    Serial.println("No I2C devices found\n");
  } else {
    Serial.println("done\n");
  }
}

//this function writes to an eeprom and location with some passed data.
void EEPROMWrite(int disk, int eepromaddress, byte eepromdata){
  Wire.beginTransmission(disk);
  Wire.write((eepromaddress >> 8));   // MSBthese two lines make sure the address gets sent correctly
  Wire.write((eepromaddress & 0xFF)); // LSB
  Wire.write(eepromdata);//data
  Wire.endTransmission();
  delay(10);//required to give it time to write
}

//function to get data from eeprom
//returns 1 for good command, 0 for error
int EEPROMRead(int disk, int startdatareadaddress, int numbytes){//numbytes cannot be bigger than 32
  if(numbytes < 33){
    Wire.beginTransmission(disk1);
    //splits the address into 2 bytes for transmission
    Wire.write(startdatareadaddress >> 8);   // MSBthese two lines make sure the address gets sent correctly
    Wire.write(startdatareadaddress & 0xFF); // LSB
    Wire.endTransmission();
    Wire.requestFrom(disk, numbytes);    // request bytes from slave device 
    return 1;
  }else{
    Serial.println("EEPROM Read error, too many bytes requested");
    return 0;  
  }
}



void setup() {  
  Serial.begin(9600);
  Serial.println("EEPROM24LC256v1");
  //start the I2C wire library
  Wire.begin();
  //scans I2C and should return an address of 0x50 if all is well
  scani2c();

  int q;
  byte nextByte;
  for(q=0;q < 10;q++){
    Serial.println("q =: "+String(q));
    EEPROMRead(disk1, q * 32, 32); //Read from disk1 starting at an address and read 32 bytes of data 

    //work through the bytes recieved
    while(Wire.available()){    // slave may send less than requested
      nextByte = Wire.read();
      Serial.println(nextByte);;
    }
  }

  Serial.println("Writing first 5 bytes");
  for(q=0;q < 5;q++){
    EEPROMWrite(disk1, q, q);  
  }
  Serial.println("Reading back first 5 bytes");
  EEPROMRead(disk1, 0, 5); //Read from disk1 starting at an address and read 32 bytes of data 

    //work through the bytes recieved
    while(Wire.available()){    // slave may send less than requested
      nextByte = Wire.read();
      Serial.println(nextByte);;
    }

}

void loop() {
  

}